Unpacking

Inside the V3 shipping carton you will find the following items:

1. V3 Tone Wheel Organ Synthesizer Module
2. AC Power Cord
3. V3 User’s Manual (this manual)
4. Warranty Registration Card.

Please return the warranty card soon after your purchase. The information you provide will help us keep you updated on new products and upgrades. We value and appreciate the information you provide us and no, we will not sell your name to any mailing lists.

Care and Precautions

When using the V3, we recommend that you adhere to the following guidelines:

1. Avoid spilling any type of liquid on the V3, be especially careful not to let any liquid fall in through the top or bottom vents as this may cause serious damage to the V3.

2. Keep the V3 away from children, especially after it’s been turned on. The V3 gets hot to the touch and although it will not get hot enough to cause burns, it may be too hot for a small child.

3. The V3 dissipates as much heat as a 25W light bulb. Keeping this in mind it may be a good idea to leave an extra space between it and other modules. Even if other modules are not near the V3, it’s a good idea to place the V3 in such a way as to allow as much air flow as possible through the air vents, both top and bottom. While the V3 is rated for 8 hours of continuous use in a non ventilated rack (continuous use in ventilated racks) other modules may malfunction due to heat buildup. Be careful not to place the V3 next to modules that are heat sensitive such an analog synths or plastic cased modules. Voce is not responsible for heat damage to other modules in a rack.

4. Although the V3 is designed to withstand the rigors of being on the road, it is not indestructible. Be especially careful of dropping it on its front side since this is its most vulnerable area due to its LCD display.

V3 Concept and How it Produces Organ Tones

How It’s Played Via MIDI

The V3 will respond to up to 3 MIDI channels. Those MIDI channels are named Upper, Lower and Pedal. The Upper and Lower MIDI channels have a range of 61 notes while the Pedal channel responds to a 25 note range. Some special features and restrictions for each of these manuals follow:

1. The Upper MIDI channel is the only channel which will respond to the Percussion effect. In the case of a split, only the upper part of the manual triggers Percussion effect.

2. The Upper Manual MIDI channel is the one whose information is displayed on the front panel. Most of the effects information is derived from the patch used on the Upper Manual MIDI channel.

3. If a split is programmed for the patch called by the Upper Manual channel, the Lower Manual MIDI channel is disabled. Its resources are diverted to the lower part of the upper manual split. This is due to a restriction of resources caused by strict adherence to B-3 architecture.

4. The Pedal MIDI channel never uses the Lowest Octave Foldback feature. The 16’ drawbar does not foldback in the lowest octave of the channel.

The only patch parameters utilized by patches called by the Lower and Pedal channels are Main Drawbar setting, Aux Drawbar Setting, Transpose and Lowest Octave Foldback (except the pedal Channel).

The Tone Generator

The sound the V3 produces starts in the tone generator section of the circuitry. Note On events transmitted by MIDI from a keyboard cause the V3 to sound some of its 91 generators at levels determined by various parameters. Key click noise and percussion are also created by the tone generator.

The most important parameters for determining which generators and what levels to be assigned are the drawbar settings. The V3 allows for two sets of drawbar settings to be used by each patch. It is possible to switch between the settings using the Morph function, which allows for a smooth transition between the two drawbar settings. Any drawbar setting may be modified in real-time by sending the appropriate MIDI control change or by changing it directly from the front panel.

Vibrato / Chorus Stage

The next stage in the signal chain is the Vibrato / Chorus circuit. Vibrato is a pleasant frequency modulation of the tones produced by the V3. Chorus is the sound produced when the vibrato sound is mixed in with a healthy portion of the original (straight) signal. Three levels of intensity for both Vibrato and Chorus effects are present in the V3.

The organ tones and keyclick are summed together to form the signal which is routed to the vibrato circuitry, while the percussion tones bypass the vibrato circuitry. There is never vibrato (or chorus) applied to percussion tones.

Expression and Effects Loop

Following the Vibrato / Chorus stage is the Expression stage. Expression is basically an equal-loudness volume control which is used by the player as a part of his or her playing style. When the Expression level is low, most of the midrange frequencies are removed from the organ sound and only some of the low and high frequencies. With the Expression level set to full the frequency response is flat and at full volume.

There is an Effects Loop provided at this stage of the audio chain for effects units such as external distortion devices, reverb, etc. The Effects Loop Output is also a good place to "grab" the straight sound of the organ before the rotating speaker effect. The Effects Loop Input is useful for sending external signals to the rotating speaker effect but it is necessary to know that plugging into the Effects Loop Input jack breaks the normal audio path, removing the organ signal. Plugging into the effects loop output does not interrupt the signal flow.

Rotating Speaker Processor

After the effects loop input comes the amplifier overdrive simulator section of the rotating speaker processor. The level of signal sent to this stage changes the amount of distortion created by this stage. This should be kept in mind when using external signals or when manipulating the expression function. The mix of overdriven to "straight" signal is controlled by patch parameters or external MIDI control changes.

The frequency, timbral, and spatial processing section of the rotating speaker effect is connected to the output of the overdrive stage. The various rates, levels and other parameters are derived from both patch information and MIDI control changes.

EQ, MIDI Volume, Output Interfaces

The next audio stage in the V3 is the equalization section. The stereo signal pair created by the rotating speaker simulator is routed to a pair of two band (Bass and Treble) equalizers which are controlled by patch parameters.

MIDI volume is the next stage which processes the stereo audio. The front panel volume control is connected after the MIDI volume stage. It then feeds the Channel 1 and 2 outputs, the headphone amplifier and the model 122 rotating speaker output. The model 122 speaker output is the mono sum of the stereo pair; its fast/slow control signal is derived from the state of the fast/slow front panel LED. This allows MIDI and patch control over the Model 122 speaker as well as the V3’s own internal rotating speaker effect.

F R O N T   P A N E L   D E S C R I P T I O N

R E A R   P A N E L   D E S C R I P T I O N

S Y S T E M    H O O K U P

 

 

P R O G R A M M I N G

The Basics

The V3 comes with 128 user programs or patches, preset from the factory. These patches can be modified by changing parameters associated with a variety of V3 functions. The V3's parameters are organized into five parameter groups. They are: Global, Patch, Rotating Speaker, MIDI Map, and Utilities. These parameters affect the V3 in different ways. Global, Rotating Speaker, MIDI Map, and Utility parameters are not patch dependent, i.e., they have an effect on the instrument regardless of what patch is selected. Patch parameters are patch dependent and only affect the instrument depending on the parameter settings for whichever patch is selected. The five parameter groups are accessed through a contiguous "flat" menu system which allows you to "scroll" through the different parameters in each parameter group.

NOTE: Throughout this manual the words "patch" and "presets" are used interchangeably.

Programming the V3 consists of five basic steps:

1. Determine what changes need to be made, i.e. Drawbar settings, MIDI channel number selection, MIDI Control number assignments, etc.

2. Enter Edit Mode. Refer to the section Entering Edit Mode for more information.

3. Select the parameters that need to be modified by turning the CURSOR control knob. Refer to the Front Panel section for a description of the CURSOR control. Refer to the next section, Menu System Description, for description of the five parameter groups as related to the V3's menuing system and to the Parameter Listing and Descriptions section for more information on the V3's parameters.

4. Make the necessary changes to each parameter by turning the DATA/PRESET control knob to set the desired value for each parameter. Refer to the Front Panel section for a description of the DATA/PRESET control. Refer to the Parameter Listing and Descriptionsfor a detailed description of each parameter. Refer to the sections on How to do the Basic Stuff, Using the Percussion Effect, Using the Rotary Speaker Effect,and Editing and Customizing MIDI Controller Maps for a detailed description of programming the V3.

5. Save your changes or exit without saving if you don't want to keep your changes. Refer to the section on Saving Your Changes/Exiting Edit Mode Without Saving.

How the V3 Stores Information

The V3 operates according to the information stored in a temporary storage called the Edit Buffer. When you power up the V3 it immediately loads the information specified by patch number 1 in the Edit Buffer. When you select a new patch, the contents of the Edit Buffer will be replaced by the information specified by the new patch. Sending control changes or adjusting certain front panel controls will also affect the contents of the Edit Buffer.

There are four ways to change the contents of the Edit Buffer:

1. Editing parameters while in Edit Mode.
   Before entering Edit Mode, the contents of the Edit Buffer is determined by the parameters specified by the selected preset or by any changes that may affect the Edit Buffer (see 2 below). The V3 uses the Edit Buffer as a scratch pad while you make changes in Edit Mode. This way your changes don't affect the patch data already programmed in the V3's memory until you decide to save them. This "non-destructive" editing allows unwanted changes to a parameter in a particular preset to be discarded without affecting the preset. Once in Edit Mode, any changes you make to any of the V3's parameters will overwrite the corresponding parameter in the Edit Buffer. The contents of the preset being edited will be overwritten by the contents of the Edit Buffer if the edits are saved.

2. Changing front panel control settings and saving the changes to the current patch.
   The V3 provides another useful and very intuitive method of data entry. When you make adjustments to the front panel controls, the contents of the edit buffer are updated for the parameter associated with this control. For Example, if you were to select the Percussion 3rd harmonic, by pressing the 2nd/3rd harmonic push button on the front panel, the 2nd/3rd harmonic select parameter would be updated in the Edit Buffer. For a listing and description of the V3's parameters, refer to section Parameter Listing and Descriptions. Similarly, any other adjustments or selections you make through the front panel controls will be reflected in the Edit Buffer. These adjustments can then be saved to the currently selected preset if desired. This is done by entering Edit Mode after making an adjustment, then saving the modified preset.

3. Sending control changes that affect the V3's settings and saving them to the current patch.
   Just as you can make adjustments and selections via the front panel control to affect the Edit Buffer as explained in item 2 above, you can do the same, including saving your changes, by sending MIDI control changes with an external MIDI controller. For more information on these control changes, refer to section Editing and Customizing MIDI Controller Mapsand to MIDI Controller Parametersin the section Parameter Listing and Descriptions.

4. Selecting a different Patch
   Whenever a patch is selected, either by an external MIDI controller via program changes or by selecting a preset via the front panel preset selector knob, the contents of the Edit Buffer is overwritten by the contents of the newly selected preset.

How the V3 Displays Information

The V3 uses a 2xl6 character, back-lit LCD display to display information. There are two basic display modes; NORMAL MODE is used when you're playing the instrument and you're not changing any of its programmed settings or making use of its built-in utilities. EDIT MODE is used when you want to program the instrument or make use of the built-in utilities. In NORMAL MODE the display will look as follows: (patch #1 shown as an example)

When in EDIT MODE, the V3 will display the information shown in the Parameter List and Descriptions.

Whenever the contents of the Edit Buffer are modified via any of the methods explained above, then a lower case "e" is displayed next to the patch number. This is to remind you that the V3 is no longer operating according to the parameters programmed in the currently selected preset. The letter "e" will remain until one of two things happen: a) a new preset is selected in which case the Edit Buffer is overwritten by the new preset's data, or b) you enter Edit Mode and save the changes, in which case the current preset is overwritten with the contents of the Edit Buffer.

Entering Edit Mode

You need to enter Edit Mode or use the Remote Save function if you would like to save any changes in the Edit Buffer as described in Programming Overview, in other words if you would like to save any changes to the currently selected patch.

To enter Edit Mode simply press the EDIT button on the front panel. Refer to the Front Panel section for a description of the EDIT button control. After pressing the EDIT button the LCD display will display the first parameter of the Global Parameters group. Next, make any necessary changes and follow the directions for exiting without saving or saving your changes and exiting.

Saving Your Changes and Exiting Edit Mode

After making all the necessary changes you can either exit without saving your changes or save your changes and exit. To save or exit without saving do the following:

1. Assuming you are in Edit Mode, press the edit button. The V3 will display the Save/Exit screen.

2. There are two ways to save the changes made in edit mode, via the front panel controls or through a remote save from an external MIDI controller. If you are saving from the front panel controls: Move the CURSOR control knob to the SAVE position if you want to save and exit or to the EXIT position if you want to exit without saving. In the latter case, all changes made in Edit Mode will remain in the Edit Buffer until you do something else to change the Edit Buffer.

3. If you want to use the V3's remote save feature: Assign the MIDI controller number of the MIDI controller you wish to use to send the REMOTE SAVE command to the V3's REMOTE SAVE CONTROL. Refer to MIDI Controller Maps for a description of the REMOTE SAVE CONTROL. After you have made your changes, send the remote save control change from your MIDI controller to save your changes. For example: if you assign a MIDI ON/OFF push button controller to the SAVE function, you can save your changes by simply pressing the push button.

Menu System Description

The V3 program menu is a contiguous flat menu system consisting of all the parameters in all five parameter groups. When you enter Edit Mode you are presented with the first parameter of the Global parameters group. To access other parameters in the menu you simply turn the CURSOR control knob on the front panel to "scroll" through the menu. If you look at the upper left hand corner of the LCD display you will notice a unique menu icon. There are five menu icons, one for each parameter group. As you scroll through different parameters within the menu you will notice that the menu icon will change to one of the other menu icons. These icons are to remind you which parameter group the displayed parameter belongs to. The five parameter groups are arranged in the same order as the parameter group descriptions shown below. The associated parameter group icon is shown in parentheses next to the parameter group name.

GLOBAL (G)	Global parameters are those which affect the operation of the instrument as a whole, regardless of which patch is selected. Instances where Global Parameters would be used include: assigning the MIDI channel number to the upper or lower manual, tuning the V3, selecting between numeric or graphic drawbar setting display, or adjusting the min and max volume settings for control pedals. Refer to the Global Parameters list in Parameter Listing and Descriptions for a detailed description of the Global Parameters and to How to do the Basic Stuff for more information on using Global parameters.
PATCH (P)	Patch Parameters are those which affect the instrument according to the value specified for the different patch parameters in the individual patches. In other words, Patch Parameters are patch dependent. Examples of Patch Parameter usage include; setting keyboard splits, editing patch names, and creating drawbar settings. Refer to the Patch Parameters list in Parameter Listing and Descriptions for a detailed description of the Patch Parameters and to How to do the Basic Stuff for more information on using Patch parameters.
ROTATING SPEAKER (R)	Rotating Speaker Parameters are specific to the 20 rotating speaker programs or setups. A rotary speaker setup is a set of specifications that define a particular rotary speaker effect which you can then assign to any of the V3's 128 patches. Each rotary speaker setup you create can consist of a different combination of such things as terminal velocity, acceleration rate, pitch modulation and even the distance and angle of the microphone to the upper and or lower rotor. Refer to the Rotating Speaker Parameters list in Parameter Listing and Descriptions for a detailed description of the Rotating Speaker Parameters and to Using the Rotary Speaker Effect for a detailed description of using and customizing the V3's rotary speaker effect.
MIDI CONTROLLER MAP (C)	MIDI Controller Map parameters are used, as the name suggests, to specify custom MIDI controller maps. You can specify up to 10 different MIDI controller maps, each with their own name and MIDI controller assignments to the V3's controls. Refer to the MIDI Controller Maps parameters list in Parameter Listing and Descriptions for a detailed description of the MIDI Controller Maps parameters and to Editing and Customizing MIDI Controller Maps for more information on using the MIDI Controller Map Parameters.
UTILITIES (U)	The utilities parameters are used for performing tasks such as re-initializing to factory settings, copying from one patch to another, and transmitting SYSEX patch dumps to an external MIDI device such a as a sequencer or editor librarian in a computer. Refer to the Utilities Parameterslist in Parameter Listing and Descriptions for a detailed description of the Utilities parameters and to How to do the Basic Stuff for more information on using the Utilities parameters.

P A R A M E T E R   L I S T I N G   A N D   D E S C R I P T I O N S

The following is a complete listing of all the parameters in the five parameter groups including a description of each parameter. This listing is meant to be used as a reference when programming the V3. The following conventions are used in the parameter descriptions:

a)  X is used to denote an alpha-numeric character for the parameter value.
b)  [choice] is used to denote a non numeric parameter value chosen from a list.
c)  [name] is used to denote a parameter value consisting of a user defined name.

GLOBAL PARAMETERS	VALUE	DISPLAY
MIDI CHANNEL UPPER MANUAL XXX Assigns the MIDI channel for the Upper Manual.	XXX = 1 - 16, OFF, OMN (OMN = OMNI)	G  MIDI CHANNEL UPPER MANUAL XXX
MIDI CHANNEL LOWER MANUAL XXX Assigns the MIDI channel for the Lower Manual.	XXX = 1 - 16, OFF	G  MIDI CHANNEL LOWER MANUAL XXX
LOWER MANUAL DEFAULT PAT XXX Assigns the default patch for the lower manual.	XXX = 1 - 128	G  LOWER MANUAL DEFAULT PAT. XXX
MIDI CHANNEL FOR PEDALS XXX Assigns the MIDI channel for the pedal manual.	XXX = I - 16, OFF	G  MIDI CHANNEL FOR PEDALS XXX
PEDAL MANUAL DEFAULT PAT XXX Assigns the default patch for the pedal manual.	XXX = 1 - 128	G  PEDAL MANUAL DEFAULT PAT. XXX
MASTER TUNING Sets the tuning for the V-3 in increments of one one-hundredth of a semitone (cents). The V-3 can be tuned up to one semitone (100 cents) above or below standard A440 tuning.	XXXX = +/- 100	G  MASTER TUNING XXXX CENTS
RELEASE CLICK [choice] Used for setting the character of the click at the release of each note.	[choice] = HARD, SLIGHTLY SOFT, SOFT, MUSHY	G  RELEASE CLICK [choice]
DRAWBAR DISPLAY Used for selecting between GRAPHIC (barline) or NUMERIC drawbar display.	[choice] = GRAPHIC, NUMERIC	G  DRAWBAR DISPLAY [choice]
GLOBAL ROTATING SPK OVERRIDE Allows the user to override the Rotating Speaker assignments of all patches and assign a single Rotating Speaker to all patches. To return to the Rotating Speaker assignments programmed into each individual patch, set this parameter to OFF.	XXX = 1 - 20, OFF	G  GLOBAL ROTATING SPK OVERRIDE
GLOBAL CONTROL MAP OVERRIDE XXX Allows the user to override the Control Map assignments of all patches and assign a single Global Map to all patches. To return to the Control Map assignments programmed into each individual patch, set this parameter to OFF.	XXX = 1 - 10, OFF	G  GLOBAL CONTROL MAP OVERRIDE
PATCH CHANGES BUTTONS? [choice] Allows the user to determine whether the parameters controlled by the front-panel buttons - such as PERCUSSION ON/OFF and PERCUSSION HARMONIC - will be altered by a new patch change, or if they remain unchanged.	[choice] = YES, NO	G  PATCH CHANGES BUTTONS? [choice]
PEDAL IN RANGE MIN XXX MAX XXX Adjusts the minimum and maximum range setting for a control pedal hooked up to the V3. Used for adapting pedal with different ranges.	XXX = 0 - 254	G  PEDAL IN RANGE MIN XXX  MAX XXX

PATCH PARAMETERS	VALUE	DISPLAY
SPLIT & MIDI NOTE# Sets the split point between the Upper and Lower Manual patches.	XXX = OFF, 1 - 127	P  SPLIT & MIDI NOTE # XXX
USE PRESET XXX FOR BELOW SPLIT Assigns a particular preset patch for the keyboard area below the split point.	XXX = 1 - 128	P  USE PRESET XXX FOR BELOW SPLIT
TRANSPOSE XXX SEMITONES Allows the user to transpose the V-3 up or down by as much as two octaves (24 semitones).	XXX = -24 to +24	P  TRANSPOSE XXX SEMITONES
P BEND RANGE XX SEMITONES Sets the maximum effect of the pitch bend wheel, in semitones (O to 12, or one octave).	XX = 0 - 12	P  P BEND RANGE XX  SEMITONES
EDIT PATCHNAME [name] Here is where the name of a new patch is recorded or an old one is edited.	[name] = any name up to 10 characters long	P  EDIT PATCHNAME [name]
DRAWBAR SETTING XXXXXXXXX The settings of the patch's 9 drawbars are displayed here in numeric format.	<XXXXXXXXX> Where X = 0 - 8	P  DRAWBR SETTING  XXXXXXXXX
AUX DB SETTING XXXXXXXXX This is the patch's auxiliary drawbar setting, for use in the DRAWBAR MORPH feature. On a B-3 tone-wheel organ there are two sets of drawbars, either of which can be engaged with the push of a button. The V-3 has this feature as well, but also allows the user to shift smoothly, or MORPH, from one drawbar setting to another. The AUX DRAWBAR SETTING is the setting into which the main setting MORPHS when this feature is engaged.	<XXXXXXXXX> Where X = 0 - 8	P  AUX DB SETTING  XXXXXXXXX
ORGAN TYPE [choice] The V-3 is currently capable of simulating three types of vintage organs: TONE WHEEL (the legendary B-3), CONTINENTAL and COMPACT, referring to popular Italian Portable organs manufactured in the 1960's. The CONTINENTAL sound can be heard on such Sixties classic tunes as "Light My Fire" by the Doors.	[choice] = TONE WHEEL, CONTINENTAL, COMPACT	P  ORGAN TYPE [choice]
GENERATOR LEAKAGE XX % This refers to the signal leakage from the tone-wheel generator into the main signal path. This sounds as if the player were holding all the keys down at once with the volume very low. This effect is an important part of the character of tone-wheel organ sound. Adjust to taste.	XX = 0 - 99	P  GENERATOR LEAKAGE XX   %
LOWEST OCTAVE FOLDBACK [choice] On the lowest octave of the B-3 tone-wheel organ, the lowest drawbar is assigned to the same harmonics as it is in the next-highest octave. This repetition is called FOLDBACK, and the user has the option of turning it ON or OFF.	[choice] = YES or NO	P  LOWEST OCTAVE FOLDBACK [choice]
EQUALIZATION BASS XXX Adjusts the equalization of the BASS frequencies, measured in dB.	XXX = +/- 12	P  EQUALIZATION BASS XXX     dB
EQUALIZATION TREBLE XXX Adjusts the equalization of the TREBLE frequencies, measured in dB.	XXX = +/- 12	P  EQUALIZATION TREBLE XXX   dB
OVERDRIVE MIX RATIO XXX % Adjusts the ratio of OVERDRIVEN signal to clean signal in the output.	XXX = 0 - 100	P  OVERDRIVE MIX RATIO XXX %
KEY CLICK LEVEL XXX % Adjusts the level of the KEYCLICK, an electrical contact noise which occurs at random volume every time a key is pressed. This is also referred to as 'spit' or 'bite' in the attack.	XXX = 0 - 100	P  KEYCLICK LEVEL        XXX %
CHORUS/VIBRATO SELECT - [choice] This is the equivalent of the vibrato controls found on the B-3 tone-wheel organ. There are three levels of "CHORUS" type vibrato (primarily amplitude modulation) and three levels of "VIBRATO" type vibrato (primarily frequency modulation).	[choice] = V1, V2, V3, C1, C2, C3, OFF	P  CHORUS/VIBRATO SELECT - [choice]
PERCUSSION ON/OFF - [choice] Turns on and off the PERCUSSION feature, which adds a transient pitch harmonically related to the fundamental of the organ tone, either at the second or third harmonic.	[choice] = ON, OFF	P  PERCUSSION ON/OFF - [choice]
PERCUSSION VOLUME [choice] Chooses between NORMAL and SOFT volume for the percussion effect.	[choice] = NORM, SOFT	P  PERCUSSION VOLUME [choice]
PERCUSSION DECAY [choice] Chooses between the SLOW and FAST decay times for the percussion effect.	[choice] = SLOW, FAST	P  PERCUSSION DECAY [choice]
PERCUSSION HARMONIC X Chooses between the SECOND or THIRD harmonic for the percussion effect.	X = 2, 3	P  PERCUSSION HARMONIC X
PERCUSSION VOLUME NORMAL POSITION Allows the user to define the volume level considered the "NORMAL POSITION" for the percussion effect.	XXX = 0 - 100%	P  PERC VOLUME NORM POS XXX %
PERCUSSION VOLUME SOFT POSITION Allows the user to define the volume level considered the "SOFT POSITION" for the percussion effect.	XXX = 0 - 100%	P  PERC VOLUME SOFT POS XXX %
PERCUSSION DECAY SLOW POSITION Allows the user to define the decay time (in seconds) considered "SLOW POSITION" for the percussion effect.	XXX = 0.5 - 6.9 seconds	P  PERC DECAY SLOW POS XXX S
PERCUSSION DECAY FAST POSITION Allows the user to define the decay time (in seconds) considered "FAST" for the percussion effect.	XXX = 0.5 - 6.9 seconds	P  PERC DECAY FAST POS XXX S
ROTATING SPEAKER [choice] Sets the state of the rotating speaker through which the organ tone is processed - either spinning FAST or SLOW, with the BRAKE on (stopped), or BYPASSED altogether. (Note that even with the BRAKE on, the signal is still being processed through the cabinet simulation.)	[choice] = FAST, SLOW, BRAKE, BYPASS	P  ROTATING SPKR [choice]
PEDAL INPUT ASSIGN [choice] Controls whether the pedal input on the back panel of the V-3 is assigned to EXPRESSION (loudness), OVERDRIVE, or VOLUME.	[choice] = EXPRESSION, OVERDRIVE, VOLUME	P  PEDAL INPUT ASSIGN [choice]
PERCUSSION VELOCITY CURVE XXX Assigns one of three velocity curves to the PERCUSSION volume, or turns velocity sensitivity off altogether.	XXX = 1 - 3, OFF	P  PERCUSSION VEL      CURVE XXX
ROTARY SPEAKER TYPE XX Assigns one of 20 user-definable ROTARY SPEAKERS to process the organ tone. LC# XX is displayed in the lower left hand corner if a global override is enabled. (xx=override type)	XX = 0 - 20 [name] is the Rotary Speaker name.	P  RS TYPE #XX     [name]
CONTROL MAP #XX Assigns one of 10 user-definable CONTROL MAPS to the patch for real time parameter manipulation. LC# XX is displayed in the lower left hand corner if a global override is enabled. (xx=override map #)	XX = 0 - 10 [name] is the Control Map name.	P  CTRL MAP #XX     [name]

ROTATING SPEAKER PARAMETERS	VALUE	DISPLAY
EDIT ROTARY SPEAKER NAME Allows the user to name a particular rotary speaker setting.	[name] = User defined Rotating Speaker name consisting of up to 10 characters	R  EDIT RSPK NAME     [name]
ROTOR BAL UPPER TO LOWER XXXX dB Adjusts the relative volume levels of the upper (horn) and lower (drum) rotors.	XXXX = +/- 12dB	R  ROTR BAL UPPER TO LOWER XXXX dB
UPPER ROTOR MIC DISTANCE XXXX Ft. Adjusts the distance of the UPPER ROTOR to the microphones.	XXXX = 0.1 - 12.7 Ft.	R  UPPER ROTOR MIC DIST XXXX Ft
UPPER ROTOR PITCH MOD XXX% Adjusts the degree to which the spinning of the upper rotor affects the pitch of the Doppler shift of the signal.	XXX = 0 - 100%	R  UPPER ROTOR PITCH MOD XXX %
UPPER ROTOR FAST RATE - Hz Adjusts the rate of the upper rotor when in FAST mode.	XXX = 0.3 - 9.3 Hz	R  UP ROTOR FAST RATE  XXX Hz
UPPER ROTOR SLOW RATE XXX Hz Adjusts the rate of the upper rotor when in SLOW mode.	XXX = 0.0 - 9.3 Hz	R  UP ROTOR SLOW RATE  XXX Hz
UPPER ROTOR ACCL RATE XXXX SEC. Adjusts the time, in seconds, that it takes for the upper rotor to ACCELERATE from its assigned SLOW rate to its assigned FAST rate.	XXXX = 0.3 - 25.4 Seconds	R  UP ROTOR ACCL RATE XXXX Sec
UPPER ROTOR DECL RATE XXXX SEC. Adjusts the time, in seconds, that it takes for the upper rotor to DECELERATE from its assigned FAST rate to its assigned SLOW rate.	XXXX = 0.3 - 25.4 Seconds	R  UP ROTOR DECL RATE XXXX Sec
UPPER ROTOR BRAKE RATE XXXX SEC. Adjusts the time, in seconds, that it takes for the upper rotor to reach a full stop when the BRAKE is applied.	XXXX = 0 - 25.4 Seconds	R  UP ROTOR BRKE RATE XXXX Sec
UPPER ROTOR MIC ANGLE XXX DEG The angle between the microphones also affects the character of the sound. This parameter essentially varies the amount of stereo separation in the signal.	XXX = 0 - 180 Degrees	R  UP ROTOR MIC ANGLE XXX DEG
LOWER ROTOR MIC DISTANCE Adjusts the distance of the microphone from the lower rotor.	XXXX = 0.1 - 12.7 Ft.	R  LOWER ROTOR MIC DIST XXXX Ft
LOWER ROTOR PITCH MOD Adjusts the degree to which the spinning of the lower rotor affects the pitch of the Doppler shift of the signal.	XXX = 0 - 100%	R  LOWER ROTOR PITCH MOD XXX %
LOWER ROTOR FAST RATE Adjusts the rate of the lower rotor when in FAST mode.	XXX = 0.3 - 9.3 Hz	R  LOW ROTOR FAST RATE  XXX Hz
LOWER ROTOR SLOW RATE Adjusts the rate of the lower rotor when in SLOW mode.	XXX = 0.0 - 9.3 Hz	R  LOW ROTOR SLOW RATE  XXX Hz
LOWER ROTOR ACCELERATION RATE - SEC. Adjusts the time, in seconds, that it takes for the lower rotor to ACCELERATE from its assigned SLOW rate to its assigned FAST rate.	XXXX = 0.3 - 25.4 Seconds	R  LOW ROTOR ACCL RATE XXXX Sec
LOWER ROTOR DECELERATION RATE Adjusts the time, in seconds, that it takes for the lower rotor to DECELERATE from its assigned FAST rate to its assigned SLOW rate.	XXXX = 0.3 - 25.4 Seconds	R  LOW ROTOR DECL RATE XXXX Sec
LOWER ROTOR BRAKE RATE XXXX SEC. Adjusts the time, in seconds, that it takes for the lower rotor to reach a full stop when the BRAKE is applied.	XXXX = 0 - 25.4 Seconds	R  LOW ROTOR BRKE RATE XXXX Sec
LOWER ROTOR MIC ANGLE See UPPER ROTOR MIC ANGLE - DEG. for explanation.	XXX = 0 - 180 Degrees	R  LOW ROTOR MIC ANGLE XXX DEG

MIDI CONTROLLER MAPS	VALUE	DISPLAY
EDIT CONTROL MAP NAME [name] Edits the assigned name for the control map.	[name] = Any user defined name up to 10 characters long.	C  EDIT CMAP NAME [name]
16' DRAWBAR CONTROL Assigns the MIDI controller number or Aftertouch for the 1st, or 16', drawbar.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  16' DRAWBAR CTRL NUMBER XXX
5-1/3' DRAWBAR CONTROL Assigns the MIDI controller number or Aftertouch for the 2nd, or 5-1/3', drawbar.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  5-1/3' DRAWBAR CTRL NUMBER XXX
8' DRAWBAR CONTROL Assigns the MIDI controller number or Aftertouch for the 3rd, or 8', drawbar.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  8' DRAWBAR CTRL NUMBER XXX
4' DRAWBAR CONTROL Assigns the MIDI controller number or Aftertouch for the 4th, or 4', drawbar.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  4' DRAWBAR CTRL NUMBER XXX
2-2/3' DRAWBAR CONTROL Assigns the MIDI controller number or Aftertouch for the 5th, or 2-2/3', drawbar.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  2-2/3' DRAWBAR CTRL NUMBER XXX
2' DRAWBAR CONTROL Assigns the MIDI controller number or Aftertouch for the 6th, or 2', drawbar.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  2' DRAWBAR CTRL NUMBER XXX
1-3/5' DRAWBAR CONTROL Assigns the MIDI controller number or Aftertouch for the 7th, or 1-3/5', drawbar.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  1-3/5' DRAWBAR CTRL NUMBER XXX
1-1/3' DRAWBAR CONTROL Assigns the MIDI controller number or Aftertouch for the 8th, or 1-1/3', drawbar.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  1-1/3' DRAWBAR CTRL NUMBER XXX
1' DRAWBAR CONTROL Assigns the MIDI controller number or Aftertouch for the 9th, or 1', drawbar.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  1' DRAWBAR CTRL NUMBER XXX
AUX 16' DRAWBAR CONTROL Assigns the MIDI controller number or Aftertouch for the 1st, or 16', auxiliary drawbar.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  AUX 16' DRAWBAR CTRL NUMBER XXX
AUX 5-1/3' DRAWBAR CONTROL Assigns the MIDI controller number or Aftertouch for the 2nd, or 5-1/3', auxiliary drawbar.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  AUX 5-1/3' DBR CTRL NUMBER XXX
AUX 8' DRAWBAR CONTROL Assigns the MIDI controller number or Aftertouch for the 3rd, or 8', auxiliary drawbar.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  AUX 8' DRAWBAR CTRL NUMBER XXX
AUX 4' DRAWBAR CONTROL Assigns the MIDI controller number or Aftertouch for the 4th, or 4', auxiliary drawbar.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  AUX 4' DRAWBAR CTRL NUMBER XXX
AUX 2-2/3' DRAWBAR CONTROL Assigns the MIDI controller number or Aftertouch for the 5th, or 2-2/3', auxiliary drawbar.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  AUX 2-2/3' DBR CTRL NUMBER XXX
AUX 2' DRAWBAR CONTROL Assigns the MIDI controller number or Aftertouch for the 6th, or 2', auxiliary drawbar.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  AUX 2' DRAWBAR CTRL NUMBER XXX
AUX 1-3/5' DRAWBAR CONTROL Assigns the MIDI controller number or Aftertouch for the 7th, or 1-3/5', auxiliary drawbar.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  AUX 1-3/5' DBR CTRL NUMBER XXX
AUX 1-1/3' DRAWBAR CONTROL Assigns the MIDI controller number or Aftertouch for the 8th, or 1-1/3', auxiliary drawbar.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  AUX 1-1/3' DBR CTRL NUMBER XXX
AUX 1' DRAWBAR CONTROL Assigns the MIDI controller number or Aftertouch for the 9th, or 1', auxiliary drawbar.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  AUX 1' DRAWBAR CTRL NUMBER XXX
DRAWBAR MORPH CONTROL Assigns the MIDI controller number or Aftertouch for the DRAWBAR MORPH function.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  DRAWBAR MORPH CTRL NUMBER XXX
MIDI VOLUME CONTROL Assigns the MIDI controller number or Aftertouch for MIDI VOLUME (Standard default is CONTROLLER #7).	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  MIDI VOLUME CTRL NUMBER XXX
MIDI EXPRESSION CONTROL Assigns the MIDI controller number or Aftertouch for EXPRESSION (a combination of volume and brightness, used in the build-in pedals of most tone-wheel organs).	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  MIDI EXPRESSION CTRL NUMBER XXX
PERCUSSION ON/OFF SWITCH CONTROL Assigns the MIDI controller number for turning the PERCUSSION effect ON and OFF.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  PERC ON/OFF SW CTRL NUMBER XXX
PERCUSSION VOLUME SWITCH CONTROL Assigns the MIDI controller number for switching between NORMAL and SOFT volume for the PERCUSSION effect.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  PERC VOLUME SW CTRL NUMBER XXX
PERCUSSION DECAY SWITCH CONTROL Assigns the MIDI controller number for switching between SLOW and FAST decay for the PERCUSSION effect.	XXX = 0 - 121, OFF	C  PERC DECAY SW CTRL NUMBER XXX
PERCUSSION HARMONIC SWITCH CONTROL Assigns the MIDI controller number for switching between the SECOND and THIRD harmonics for the PERCUSSION effect.	XXX = 0 - 121, OFF	C  PERC HARM SW CTRL NUMBER XXX
CHORUS/VIBRATO ON/OFF CONTROL Assigns the MIDI controller number for turning the CHORUS/VIBRATO effect ON and OFF.	XXX = 0 - 121, OFF	C  C/VIB ON/OFF CTRL NUMBER XXX
CHORUS/VIBRATO SELECT CONTROL Assigns the MIDI controller or Aftertouch number for choosing between the three CHORUS effects and the three VIBRATO effects.	XXX = 0 - 121, OFF	C  C/VIB SELECT CTRL NUMBER XXX
ROTARY SPEAKER BYPASS CONTROL Assigns the MIDI controller number for the ROTARY SPEAKER BYPASS function.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  ROT SPKR BYP CTRL NUMBER XXX
ROTARY SPEAKER SLOW/FAST CONTROL Assigns the MIDI controller number for switching the rotary speaker between SLOW and FAST speeds.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  ROT SPKR SL/FAST CTRL NUMBER XXX
ROTARY SPEAKER BRAKE CONTROL Assigns the MIDI controller number for the ROTARY SPEAKER BRAKE function.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  ROT SPKR BRAKE CTRL NUMBER XXX
OVERDRIVE MIDI CONTROL Assigns the MIDI controller number which adjusts the amount of OVERDRIVE.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  OVERDRIVE MIDI CTRL NUMBER XXX
KEY CLICK MIDI CONTROL Assigns the MIDI controller number which adjusts the amount of KEY CLICK.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  KEY CLICK MIDI CTRL NUMBER XXX
LEAKAGE MIDI CONTROL Assigns the MIDI controller number which adjusts the amount of GENERATOR LEAKAGE.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  LEAKAGE MIDI CTRL NUMBER XXX
UPPER ROTOR MIC DISTANCE CONTROL Assigns the MIDI controller number which adjusts the amount of MIC DISTANCE for the upper rotor.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  UPR ROTOR MIC DIST CTRL # XXX
UPPER ROTOR PITCH MODULATION CTLR Assigns the MIDI controller number which adjusts the amount of PITCH MODULATION for the upper rotor.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  UPR ROTOR PITCH MOD CTRL # XXX
UPPER ROTOR FAST CONTROL Assigns the MIDI controller number which adjusts the FAST speed of the upper rotor.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  UP ROTOR FAST CTRL NUMBER XXX
UPPER ROTOR SLOW CONTROL Assigns the MIDI controller number which adjusts the SLOW speed of the upper rotor.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  UP ROTOR SLOW CTRL NUMBER XXX
UPPER ROTOR ACCELERATION CONTROL Assigns the MIDI controller number which adjusts the ACCELERATION RATE of the upper rotor.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  UP ROTOR ACCL CTRL NUMBER XXX
UPPER ROTOR DECELERATION CONTROL Assigns the MIDI controller number which adjusts the DECELERATION RATE of the upper rotor.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  UP ROTOR DECL CTRL NUMBER XXX
UPPER ROTOR BRAKE CONTROL Assigns the MIDI controller number which adjusts the BRAKE RATE of the upper rotor.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  UP ROTOR BRKE CTRL NUMBER XXX
UPPER ROTOR MIC ANGLE CONTROL Assigns the MIDI controller number which adjusts the MIC ANGLE of the upper rotor.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  UP ROTOR MIC ANG CTRL NUMBER XXX
LOWER ROTOR MIC DISTANCE CONTROL Assigns the MIDI controller number which adjusts the amount of MIC DISTANCE for the lower rotor.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  LOW ROTOR MIC DIST CTRL # XXX
LOWER ROTOR PITCH MODULATION CTLR Assigns the MIDI controller number which adjusts the amount of PITCH MODULATION for the lower rotor.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  LOW ROTOR PITCH MOD CTRL # XXX
LOWER ROTOR FAST CONTROL Assigns the MIDI controller number which adjusts the FAST speed of the lower rotor.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  LOW ROTOR FAST CTRL NUMBER XXX
LOWER ROTOR SLOW CONTROL Assigns the MIDI controller number which adjusts the SLOW speed of the lower rotor.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  LOW ROTOR SLOW CTRL NUMBER XXX
LOWER ROTOR ACCELERATION CONTROL Assigns the MIDI controller number which adjusts the ACCELERATION RATE of the lower rotor.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  LOW ROTOR ACCL CTRL NUMBER XXX
LOWER ROTOR DECELERATION CONTROL Assigns the MIDI controller number which adjusts the DECELERATION RATE of the lower rotor.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  LOW ROTOR DECL CTRL NUMBER XXX
LOWER ROTOR BRAKE CONTROL Assigns the MIDI controller number which adjusts the BRAKE RATE of the lower rotor.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  LOW ROTOR BRKE CTRL NUMBER XXX
LOWER ROTOR MIC ANGLE CONTROL Assigns the MIDI controller number which adjusts the MIC ANGLE of the lower rotor.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  LOW ROTOR MIC ANG CTRL NUMBER XXX
ROTOR BALANCE CONTROL Assigns the MIDI controller number which adjusts the volume BALANCE between the upper and lower rotors.	XXX = 0 - 121, AFT, OFF AFT = AFTER-TOUCH	C  ROTOR BAL CTRL NUMBER XXX
REMOTE SAVE CONTROL Assigns the MIDI controller number to the remote save function. Works the same as the front panel save function.	XXX = 0 - 121, OFF	C  REMOTE SAVE CTRL NUMBER XXX
SUSTAIN PEDAL CONTROL Assigns the MIDI controller number to the note hold function. Usually assigned to number 64.	XXX = 0 - 121, OFF	C  REMOTE SAVE CTRL NUMBER XXX

UTILITIES PARAMETERS	VALUE/DESCRIPTION	DISPLAY
TRANSMIT SYSEX PATCH DUMP This causes the V-3 to transmit a system exclusive dump of all patches, rotary speakers and control maps.	Turn DATA/PRESET control to initialize patch dump.	U  XMIT SYSEX PAT DUMP [TURN DATA]
	Displayed when PATCH DUMP is in progress.	U  XMIT SYSEX PAT XMITING PLS WAIT
RE-INITIALIZE MEMORY This utility completely erases all user-programmed data from the V-3's memory and reinstalls the factory patches, rotary speakers and control maps.	Set XX to 50 to re-initialize	U  RE-INITIALIZE [SET TO 50] XX
COPY FROM PATCH # TO PATCH # This utility allows the user to copy a single patch from one location to another.	A = Source Patch B = Destination Patch	U  COPY FROM PAT #A         to #B
	[choice] = YES or NO	U  COPY PATCH??? X#A         to #B [choice]
	If [choice] is YES, then Copy Complete message is displayed.	U  PATCH COPIED! X#A         to #B  YES
COPY FROM ROTARY SPEAKER # TO ROTARY SPEAKER # This utility allows the user to copy a specific rotary speaker setup to another.	A = Source Rotary Speaker B = Destination Rotary Speaker	U  COPY FROM RSPK #A         to #B
	[choice] = YES or NO	U  COPY R. SPEAKER? X#A         to #B [choice]
	If [choice] is YES, then Copy Complete message is displayed.	U  R. SPK COPIED! X#A         to #B  YES
COPY MIDI MAP? This utility is used for copying the contents of one MIDI MAP, the source map, to another, the destination MIDI MAP.	A = Source MIDI MAP B = Destination MIDI MAP	U  COPY FROM MMAP #A         to #B
	[choice] = YES or NO	U  COPY MIDI MAP? X#A         to #B [choice]
	If [choice] is YES, then Copy Complete message is displayed.	U  M MAP COPIED! X#A         to #B  YES
SEE MIDI DATA This is a utility screen which displays MIDI data activity. Useful for monitoring MIDI setup and to verify that a MIDI controller is communicating with the V3.	Displayed when there is no MIDI activity or if the V3 is not receiving MIDI data due to a fault in the MIDI setup.	U  SEE MIDI DATA NO DATA RECEIVED
	If there is MIDI data activity, it will display MIDI status and channel data on the lower row of the LCD display.	U  SEE MIDI DATA [midi data activity]

H O W   T O   D O    T H E   B A S I C   S T U F F

This section helps you get right down to the nitty gritty of programming the V3. The following is a listing of procedures for programming those things which are most common when using the V3. When performing any of the following procedures, it is assumed that you have read the previous section, Programming the V3, and that you understand how to enter Edit Mode and how to save your changes once you are done editing. It is also assumed that you are already in Edit Mode. Parameters will be referred to by their name and to further aid in finding specific parameters called out in each procedure, the parameter group icon will be shown in parentheses following the parameter name. When in Edit Mode, you select the parameters you which to edit by turning the CURSOR control knob until the desired parameter is displayed. You then select the parameter value by turning the DATA/PRESET control knob to the desired value. You may want to refer to the Parameter Listing and Descriptions for a description of each parameter and a listing of valid parameter values while performing any of the following procedures.

Tuning the V3

This is the global tuning parameter for the instrument. It affects all the patches equally. This tuning control allows the user to set the pitch of the instrument to be within a semitone of A440. To tune the instrument:

1. Select MASTER TUNING XXX CENTS (G).

2. Set the data value of XXX to be within the range of -100 cents to +100 cents.

Assigning the MIDI Channel

The V3 allows you to assign a MIDI channel to the upper manual, lower manual, and bass pedals. If you are using two manuals, one manual gets assigned to one MIDI channel and the other to a different MIDI channel. If only one manual is being used, then the upper manual should be assigned to whatever MIDI channel you would like to assign to your MIDI controller and the lower manual should be set to OFF. If you are using MIDI bass pedals you can assign a MIDI channel for this controller also. To assign the MIDI channel to the upper and lower manual and to bass pedals, do the following:

1. Select MIDI CHANNEL - UPPER MANUAL (G) for setting the upper manual MIDI channel assignment, MIDI CHANNEL - LOWER MANUAL (G) for setting the lower manual MIDI channel assignment, or MIDI CHANNEL FOR PEDALS (G) for setting the MIDI bass pedal channel assignment.

2. Set the channel number to the desired MIDI channel (1-16 or OMNI for the upper manual, 1-16 for the lower manual and bass pedals.) for either the upper manual, lower manual, or MIDI bass pedals. If using only one manual, set the channel number to the desired channel (1 - 16 or OMNI) for the upper manual then select MIDI CHANNEL - LOWER MANUAL (G) and set the MIDI channel to OFF. Upper manual 0MMI supercedes all other channels.

Adjusting the Release and Attack Key Click

The V3 allows you to adjust the amount of attack key click and the amount of release key click. Key click is caused by a combination of contact noise and voltage transient whenever a note is pressed or released. This clicking or popping sound although considered a flaw in the original tone wheel organ design, is actually an integral part of the tone wheel organ sound (B3, C3, M3 etc..). However there are those who don't like this type of "effect" or simply find that key click is just too annoying. This effect is also what is know as "SPIT" or "BITE". If you prefer your organ sound a little less aggressive then you may want to turn down the amount of key click.

The attack key click can be adjusted differently for each patch. However, the release click adjustment is global. To adjust the amount of attack key click:

1. Select the patch where you want to make the key click adjustment, enter Edit Mode, then select parameter KEY CLICK LEVEL (P).

2. Play some notes on your keyboard and adjust level to taste. Set between 0 to 100 %.

To adjust the amount of release click:

1. Select RELEASE CLICK (G). (from any patch)

2. Play some notes on your keyboard switching between HARD, SLIGHTLY SOFT, SOFT, and MUSHY. Notice the change in character of the release click as you switch between the four Levels. Then set it to the desired level.

Selecting how the Drawbar Settings are Displayed

The V3 has two drawbar settings styles. Graphical and numerical. The graphical display style consists of nine vertical bars of varying height depending on the individual drawbar settings. These are displayed from left to right on the LCD display. The numerical display style consists of nine numbers displayed from left to right on the display showing the exact value of each drawbar setting. The display style setting is global, meaning that once a display style is chosen it will apply to all patches until it is changed again. To select the drawbar display method: (NORMAL MODE only)

1. Select DRAWBAR DISPLAY (G)

   NOTE:  This affects NORMAL MODE only. In EDIT MODE, the drawbar display is always numeric.

2. Set to GRAPHIC or NUMERIC by turning the DATA/PRESET knob left or right.

Let Patch Changes Alter the States of the Front Panel Push Buttons

The state of the front panel push buttons can be forced to the settings of the selected patch or they can remain at whatever state they were in before a new patch was selected. This is useful if you want to use the push button to control your settings and don't want to have to keep resetting them each time you select a new patch. This features only applies to those parameters corresponding to the front panel push buttons. Refer to FRONT PANEL for a description of the front panel push buttons. To allow patch changes to affect the state of the push buttons, do the following:

1. Select PATCH CHANGES BUTTONS (G).

2. Set to YES if you want patch changes to affect the state of the push buttons, set to NO if you want the state of the push buttons to remain unchanged as you select different patches.

Set Keyboard Splits

The V3 allows the user one split for the upper manual MIDI channel only. This is very useful when using only one keyboard to play the V3. The procedure of setting a split is as follows:

1. Select SPLIT @ MIDI NOTE # XXX (P).

2. Set the data value of XXX to be the MIDI note number which you'd like the split point to be.

3. Select USE PRESET XXX FOR BELOW SPLIT (P).

4. Set the data value of XXX to be the split patch which will play below the split note. Using the split features disables the lower manual channel.

Set Note Transposition

The V3 lets you transpose up or down by as much as two octaves (24 semitones). This allows you to either play in a different key or to better utilize a smaller keyboard in order to access a specific note range. To transpose the V3 do the following:

1. Select TRANSPOSE BY XXX SEMITONES (P).

2. To transpose up by 1 to 24 semitones set to +1 to +24 in increments of one semitone. To transpose down by 1 to 24 semitones, set to -1 to -24 in increments of one semitone.

Set the Amount of Pitch Bend

You can control the pitch bend from your MIIDI controller's pitch bend wheel. To specify the amount of effect from the pitch bend wheel, do the following:

1. Select P BEND RANGE = XX SEMITONES (P).

2. Set the amount of pitch bend to 0 for no pitch bend or to anywhere from 1 to 12 semitones. To help you set the right amount of pitch bend, turn the pitch bend wheel while adjusting the amount of pitch bend on the V3.

Editing the Patch Name

All of the V3's 128 patches come preset from the factory with a unique patch name. Since all of the V3's patches are programmable, they can also be renamed using up to 10 characters per name. To rename an old patch or to name a new one, do the following:

1. Select EDIT PATCH NAME (P).

2. The cursor will appear under the the left most or right most character of the patch name depending on which direction the cursor knob is being turned. Select the desired character for each character position with the DATA/PRESET control knob. You can use up to 10 characters per name. Note that when you scroll through the menu, the cursor passes through each character in the name before advancing to the next menu item.

Create Drawbar Settings

One of the most powerful features of the V3 is the ability to create any combination of drawbar settings. There are nine ÒsoftÓ drawbars in the V3, each of which can bet set from 0 to 8. A drawbar setting consists on any combination of the nine drawbars. Each patch contains two drawbar settings, the Main Drawbar Setting and the Auxiliary Drawbar Setting. Drawbars are represented either graphically or numencally on the V3's LCD display. Refer to Selecting how the Drawbar Settings are Displayed discussed earlier for more information on the drawbar display. To program your own drawbar setting in a V3 patch, do the following:

1. Select DRAWBAR SETTING (P) to program a main drawbar setting or AUX SETTING (P) to program an auxiliary drawbar setting.

2. Move the cursor under the individual drawbar settings you wish to modify and set the value of each drawbar by turning the DATA/PRESET control knob.

Morphing Between two Drawbar Settings

1. Select parameter DRAWBAR MORPH CONTROL (C).

2. Assign the MIDI controller number for your MIDI controller to the drawbar morph function. Note that in order to get the morphing effect, the controller assigned to the morph function must be a continuous controller such as a MOD Wheel. If the controller assigned to the morph function is an ON/OFF type MIDI controller, then the morphing effect is lost since the two drawbar settings will simply switch instantly one or the other.

Select One of the Three Organ Types

The V3 is capable of simulating three types of organ: Tone Wheel Organ such as the B3, and two types of electronic organs; Continental, and Compact. Almost all of the factory patches are Tone Wheel Organ type. To switch to another organ type, do the following:

1. Select parameter ORGAN TYPE (P).

2. Select the desired organ type by turning the PRESET/DATA control knob.

Adjust the Amount of Tone Generator Leakage

Tone generator leakage is basically the crosstalk between the tone generators of a Tone Wheel organ. This is actually a flaw in the original tone wheel organs but eventually people got used to it and it became part of the "B-3" sound. The V3 allows you to add generator leakage to any of its patches. The amount of leakage can be adjusted to taste. To add or remove generator leakage to a patch, do the following:

1. Select the parameter GENERATOR LEAKAGE (P).

2. Adjust the amount of leakage from 0% for no leakage to 99% for lots of leakage. You may want to play some notes on your keyboard as you adjust the amount of leakage.

Enable/Disable the Low Octave Harmonic Foldback Feature

On the lowest octave of a B-3 tone wheel organ, the lowest drawbar (16') is assigned to the same harmonics as it is in the next highest octave. This repetition is called Foldback and the user has the option of turning it ON or OFF. By turning Foldback off, you can allow the notes of the lowest octave to play as they normally would with out foldback, i.e., the pitch gets lower. To disable or enable Lowest Octave Harmonic Foldback, do the following:

1. Select the parameter LOWEST OCTAVE FOLDBACK (P).

2. Set FOLDBACK to ON or OFF as desired.

Adjust the Bass and Treble

The V3 comes with built in EQ allowing you to adjust the Bass and Treble frequencies. The V3's bass and treble can be adjusted differently on each of its 128 patches. To adjust the bass and treble, do the following:

1. Select the parameter BASS EQUALIZATION (P) if you wish to adjust the amount of Bass or select TREBLE EQUALIZATION (P) if you wish to adjust the amount of Treble.

2. Turn the DATA/PRESET control knob to adjust the amount of Bass or Treble by +/- 12 dB. While making the adjustment, play some notes on your keyboard and adjust to taste.

Adjust the Overdrive to Clean Signal Ratio

1. Select the parameter OVERDRIVE MIX RATIO XXX % (P).

2. Turn the DATA/PRESET control knob to adjust the amount of overdriven signal to clean signal (0 - 100 %, 100% = all overdriven signal).

Controlling Expression Using a Foot Pedal

As with most traditional tone wheel organs, the V3 makes use of Expression, which is a combination of volume and brightness. The V3's expression function can be controlled via MIDI or with a potentiometer type pedal, such as a volume pedal. To control Expression via MIDI, you need to assign a continuous MIDI controller to Expression. To control Expression using the V3's rear panel pedal input, you must assign the pedal input to Expression for a particular patch or patches.

To control Expression via MIDI, do the Following:

1. Select the parameter MIDI EXPRESSION CONTROL (C).

2. Assign the MIDI controller number for the MIDI controller you will be using to control Expression.

To control expression via the rear panel pedal input, do the following:
Note:  See sidebar for Expression Pedal specification.

1. Select the parameter PEDAL INPUT ASSIGN (P).

2. Turn the DATA/PRESET control and select EXPRESSION.

When using the rear panel pedal input for controlling expression, keep in mind that the V3 comes pre-calibrated from the factory to work with a variety of expression pedals. Depending on the brand of pedal being used for controlling expression, it may be necessary to calibrate the V3 to work for your particular pedal. If the action of your expression pedal sounds irregular, i.e., transition between soft and loud is too sudden, then it may be that the V3 has to be calibrated for your pedal.

To calibrate the V3's expression pedal input for a particular pedal, do the following:

1. Select the parameter PEDAL IN RANGE MIN XXX MAX XXX (P).

2. With your pedal plugged into the V3's pedal input jack, set the MAX value to 254. Press the pedal all the way down and play a constant note. Start decreasing the MAX value until you just start hearing the output level start to decrease, then back off just a bit. Try to leave the MAX value at the point just before the level begins to drop. Now you have to set the MIN value. While still paying a constant note, let go of the pedal until it's all the way up. Set the MIN value to 0. Then, start increasing the MIN value just until the level starts to increase then, back off just a bit. Try to leave the MIN value at the point just before the level begins to increase.

Controlling the V3's Overdrive using a Foot Pedal

The V3 is able to simulate the effect of an overdriven vacuum tube power amp. The V3's overdrive effect can be controlled via MIDI or with a potentiometer type pedal, such as a volume pedal. To control Overdrive via MIDI, you need to assign a continuous MIDI controller to Overdrive. To control Overdrive using the V3's rear panel pedal input, you must assign the pedal input to Overdrive for a particular patch or patches.

To control Overdrive via MDI, do the Following:

1. Select the parameter OVERDRIVE MIDI CONTROL (C).

2. Assign the MIDI controller number for the MIDI controller you will be using to control Overdrive.

To control Overdrive via the rear panel pedal input, do the following:

1. Select the parameter PEDAL INPUT ASSIGN (P).

2. Turn the DATA/PRESET control and select OVERDRIVE.

Set the Chorus and Vibrato Effects Level

The Chorus and Vibrato effect can be enabled for individual patches. In addition, just like in the B-3 tone wheel organ, you have a choice of three levels of chorus or vibrato to choose from. To set the level of the chorus or vibrato effect, do the following:

1. Select the parameter CHORUS/VIBRATO SELECT (P).

2. Turn the DATA/PRESET control and select your choice of CHORUS levels (C1,C2,C3) or VIBRATO levels (V1, V2, V3) or OFF for no effect.

Using Note Velocity with the V3 Percussion Effect

1. Select the parameter PERCUSSION VELOCITY CURVE XXX (P).

2. Turn the DATA/PRESET control and select your choice of OFF (no velocity sensitivity) or 1-3 different curve sensitivities.

Using After-touch with the V3

Referring to the parameter chart it may be seen that most of the MIDI controller assignments can alternately be assigned to aftertouch. If a function which normally uses a continuous controller is assigned aftertouch, the functions value will increase proportionally with both note and channel pressure. It the function assigned to after-touch is an on/off type, Aftertouch pressure will toggle the function.

Transmit SYSEX Patch Dump to External MIDI Devices

To transmit a bulk dump of all non-volatile parameters stored on the V3 perform the following:

1. Select the parameter XMIT SYSX PATCH DUMP (U) located in the Utilities menu section.

2. Turn the DATA/PRESET control clockwise. Dump is performed within 6 seconds.

Re-initialize the V3's Program Memory to Factory Settings

The V3 comes pre-programined with 128 factory patches. These patches can be overwritten with your own patches and if necessary, you can restore or re-initialize to factory settings any time afterwards. To restore factory settings, do the following:

1. Select the parameter RE-INITIALIZE MEMORY (U).

2. Turn the DATA/PRESET control and set the value to 50. The V3 will begin the Re-Initialization procedure and after approximately 10 seconds will return you to the normal menu on patch #1.

Copy Patch Settings from one Patch to Another

It is possible to copy the information from one patch to another patch. For example, you may want to organize your patches in such a way that it becomes necessary to copy patch # 45, the source patch, to patch # 62, destination patch. The information in the destination patch will be overwritten by the information in the source patch. To copy from one patch to another, do the following:

1. Select parameter COPY FROM PATCH # to PATCH # (U). The LCD display will read as shown in Menu 1 where A is the source patch and B is the destination patch.

2. Move the cursor to the source patch # on the left hand side of the display and select the source patch number. Then, move the cursor to the destination patch number on the right hand side of the display and select the destination patch number.

3. Move the cursor once more to the right. The display should now read as shown in Menu 2. Turn the DATA/PRESET control and set to [choice] to YES, the display will now read as shown in Menu 3. You have just copied the source patch to the destination patch.

U S I N G   T H E    P E R C U S S I O N   E F F E C T

The percussion effect is an integral part of the B-3 tone wheel organ sound. The percussion effect adds a transient while a note is played that is harmonically related to the organ's fundamental tone by either the second or third harmonic. This effect is a single-trigger effect, meaning that it will not re-trigger when playing more than one note at a time. And, when playing one note at a time, it will not sound on a second note until you let go of the first note. The V3 provides full control over the Percussion Effect on a patch by patch basis, allowing you to program a different Percussion Effect setting for each patch. The character of the Percussion Effect is determined by: the Percussion Volume, Decay Time, which harmonic of the fundamental it occurs at, and note velocity. When using note velocity you can select different velocity curves which specify how loud the Percussion Effect will sound depending on how hard you strike a key. In addition, you can define different variations of Percussion Volume and Decay Time from which to choose from within a particular patch. For example; you can define the percussion volume NORMAL and SOFT within a patch then switch between the two settings by sending the appropriate MIDI control changes. The following procedures who how to use the various parameters associated with the Percussion Effect to create your own Percussion Effect settings.

Enabling the Percussion Effect

The Percussion Effect can be enabled on a patch by patch basis. To enable the Percussion Effect for a certain patch, do the following:

1. Select the parameter PERCUSSION ON/OFF (P).

2. Select ON of OFF as desired.

Adjusting the Percussion Decay Time

The Percussion Decay Time can be set to either SLOW or FAST decay on a patch by patch basis. To set the Percussion Decay Time, do the following:

1. Select the parameter PERCUSSION DECAY TIME (P).
2. Select SLOW or FAST as desired.
3. Select the parameter PERCUSSION DECAY SLOW POSITION (P).
4. Adjust the value for the SLOW position level.
5. Select the parameter PERCUSSION DECAY FAST POSITION (P).
6. Adjust the value for the FAST position level.

Percussion Volume Settings and Adjustments

Adjusting the Percussion Volume consists of selecting either the NORMAL or SOFT volume setting on a particular patch, then setting the level you want the NORMAL and SOFT position to be. To adjust Percussion Volume do the following:

1. Select the parameter PERCUSSION VOLUME (P).
2. Select either the NORMAL or SOFT setting.
3. Select the parameter PERCUSSION VOLUME NORMAL POSITION (P).
4. Adjust the value for the NORMAL position level.
5. Select the parameter PERCUSSION VOLUME SOFT POSITION (P).
6. Adjust the value for the SOFT position level.

Note:  To help make your adjustments, try playing some notes on your keyboard while performing steps 4 and 6 above.

Selecting Percussion 2nd or 3rd Harmonic

Each V3 patch can be assigned a default Percussion Harmonic setting, either 2nd or 3rd harmonic. To assign the Percussion Harmonic setting, do the following:

1. Select the parameter PERCUSSION HARMONIC X (P).

2. Set the value (X) to either 2 for 2nd harmonic or 3 for 3rd harmonic.

Using Velocity to Control Percussion

The V3 allows you to use MIDI Note Velocity to control the Percussion Volume. This is accomplished by assigning one of three velocity curves which determine the Percussion volume depending on how hard you strike a key. This allows you to play similarly to the way you would play a piano where the harder you strike a key, the louder it will sound. Without Percussion Velocity, the Percussion volume will always be at the default setting regardless of how hard you strike a key. To use the Percussion velocity feature, do the following:

1. Select the parameter PERCUSSION VELOCITY CURVE XXX (P).

2. Set the value (XXX) to 1,2,3 for one of the three velocity curves. Setting the value to OFF will disable Percussion Velocity, forcing the Percussion volume to the default setting.

Controlling Percussion through MIDI

The V3 allows you to control the Percussion Effect through external MIDI controllers. Specifically, you can use a MIDI ON/OFF switch to select between the NORMAL and SOFT Percussion Volume settings, to switch between 2nd and 3rd Percussion Harmonic, to switch the Percussion Effect on or off, and to switch between SLOW and FAST percussion decay time. To control the various Percussion Effect parameters via MIDI, do the following:

1. Select the MIDI controller map parameter you wish to control via MIDI; PERCUSSION ON/OFF SWITCH CONTROL, PERCUSSION VOLUME SWITCH CONTROL, PERCUSSION HARMONIC SWITCH CONTROL, or PERCUSSION DECAY SWITCH CONTROL (C).

2. Assign the MIDI control number of each MIDI ON/OFF controller for each of the above Percussion parameters you wish to control.

U S I N G   T H E    R O T A R Y   S P E A K E R   E F F E C T

The rotary speaker effect is an integral part of the "B-3 sound". No B-3 tone wheel organ simulation would be complete without this effect. The V3 provides a rotary speaker effects that simulates the rotary speaker setups typically used with the B-3 tone wheel organ. These consist of "miked" up stock and modified rotary speakers. The V3 comes with ten factory programmed rotary speaker setups which can be modified by the user. There is enough space in the V3's program memory for ten additional setups which can be created by the user, providing a total of twenty setups. Any of these rotary speaker setups can be assigned to any of the V3's 128 patches. A rotary speaker setup consists of variations in parameters that affect such things as rotor balance, microphone distance and angle, rotor pitch modulation, acceleration and deceleration rates, rotor terminal velocity and brake rates. These parameters allow you to create custom setups that were not even possible to create with real rotary speakers. Refer to the procedures listed below to create and modify rotary speaker setups.

Assigning a Rotary Speaker Setup to a Patch

To assign one of the 20 rotary speaker setups to any of the V3's 128 patches first make sure you are editing the patch where you want to make the assignment, then do the following:

1. Select parameter ROTARY SPEAKER TYPE (R).

2. Select the rotary speaker type number (XX), the name of the particular rotary speaker setup will be displayed as you select the rotary speaker number.

Naming Rotary Speaker Setup

You can give a unique name to any of the 20 rotary speaker setups. To name a rotary speaker setup, do the following:

1. Select parameter EDIT ROTARY SPEAKER NAME (R).

2. The cursor will fall under the left-most or right-most character position, depending on which direction you were turning the cursor knob. Select a letter for each character position by tuming the DATA/PRESET control knob. You can use up to 10 characters per name.

Adjusting the Rotor Balance

You can adjust the relative volume level between the upper and lower rotor, or rotor balance. To adjust the rotor balance, do the following:

1. Select parameter ROTOR BAL UPPER TO LOWER XXX dB (R).

2. Adjust the value (XXX) expressed in decibels (dB) by +/- 12 dB. It may be helpful to play some notes on your keyboard while making this adjustment.

Setting the Upper/Lower Rotor Microphone Distance

In the recording studio, the character of a rotary speaker's sound can vary dramatically depending on how it is "miked". This parameter can be used to simulate a close-"miked" sound, with deep amplitude modulation, or a far-"miked" sound, with much less amplitude modulation. To adjust the mike distance of either the upper or lower rotor, do the following:

1. Select parameter UPPER ROTOR MIC DISTANCE XXXX Ft. OR LOWER ROTOR MIC DISTANCE XXXX Ft. (R)

2. Set the mike distance in in increments of 0.1 feet,from 0.1 to 12.7 feet for either the upper or lower rotor.

Setting the Upper/Lower Rotor Pitch Modulation

The spinning effect of either the upper or lower rotor of a rotary speaker system will affect the pitch of the fundamental of the audio signal being generated. Because the V3's rotary speaker effect is programmable, you have the option of adjusting the amount of pitch modulation caused by the spinning rotor. To adjust pitch modulation, do the following:

1. Select parameter UPPER ROTOR PITCH MOD XXX % or LOWER ROTOR PITCH MOD XXX % (R).

2. Set the amount of pitch modulation of either the lower rotor or upper rotor to taste. While making this adjustment, play some notes on your keyboard with the rotary speaker effect on and listen to the effect of the changes in pitch modulation.

Setting Upper/Lower Rotor Slow/Fast Rate

In a real rotary speaker, the final rotation velocity at either the slow or fast rate, is determined by a mechanical system consisting of belts and pulleys. The terminal velocity is limited to three fixed rates which can be adjusted by setting the belts to one of three different pulley positions. Rather than limiting you to three fixed rates, the V3's rotary speaker effect terminal velocity can be adjusted incrementally between 0.3 to 9.3 Hz for the fast rate and between 0.0 to 9.3 Hz for the slow rate. This provides a way of making finer adjustments, thus allowing for more customization. To adjust the upper or lower rotor terminal velocity for either the slow or fast speed, do the following:

1. Determine which terminal velocity you which to adjust and select the corresponding parameter, either UPPER ROTOR FAST RATE XXX SEC, or UPPER ROTOR SLOW RATE XXX SEC,or LOWER ROTOR SLOW RATE XXX SEC, or LOWER ROTOR FAST RATE XXX SEC (R).

2. Set the rate (XXX) to the desired frequency in increments of 0.1 Hz. Although the increments are 0.1 Hz, the changes in frequency are not really noticeable until you change it by at least 0.3 Hz. Play some notes on your keyboard with the rotary speaker effect set at whatever speed you are adjusting (SLOW or FAST) and listen to the change in rotor velocity. Adjust to taste. Repeat this step for each rotor, and rotor velocity you wish to adjust.

Adjusting the Upper/Lower Rotor Acceleration/Deceleration Rate

A real rotary speaker is an electro-mechanical system consisting of two rotating horns for the treble frequencies and a rotating drum for the lower frequencies. The rotation comes from a series of belts and pulleys driven by four motors, two for each rotor (one for the fast rate and one for the slow rate). Because the rotors have a mass associated with them, when you change speeds from SLOW to FAST or vice versa, the change in speed is not instantaneous, rather there is a time lag or delay otherwise known as the speed-up time or the slow-down time, which is directly related to the acceleration rate. Additionally, since the lower rotor or drum has more mass the upper rotor, it takes more time to speed-up or slow down than the upper rotor. Also, on a real rotary speaker, the acceleration rate is fixed for each combination of belt and pulley settings and may vary depending on the imperfections and age of the internal components of the rotary speaker system. The V3 provides a way of adjusting the acceleration and deceleration rates of the upper and lower rotors independently by allowing you to specify the speed-up time and the slow-down time from 0.3 to 24.4 seconds. To adjust the rotor acceleration/deceleration rates, do the following:

1. Select the parameter corresponding to which rotor you want to adjust the acceleration or deceleration rate, i.e. UPPER ROTOR ACCL RATE XXXX SEC, or UPPER ROTOR DECL RATE XXXX SEC, or LOWER ROTOR ACCL RATE XXXX SEC, or LOWER ROTOR ACCL RATE XXXX SEC (R).

2. Set the rotor speed-up time (XXXX) for acceleration rate adjustments to the desired delay time. Set the slow-down time (XXXX) for deceleration rate adjustments to the desired delay time. Play some notes on your keyboard with the rotary speaker effect turned on and listen to the change in speed-up time and slow-down time as you switch between SLOW and FAST rotor velocity. Adjust to taste. Repeat this step for each rotor, and rotor acceleration and deceleration setting you which to adjust.

Setting Upper/Lower Rotor Brake Rate

The brake function on a rotary speaker allows you to stop the rotation of the upper and lower rotor. Although the rotors will no longer be spinning when the brake is on, sound will still be emanating from the rotary speaker system. When the brake is on, the rotary speaker does not simply stop instantaneously, rather it comes to rest gradually. Additionally, since the lower rotor or drum has more mass than the upper rotor, it takes more time to come to rest than the upper rotor. The time it takes for the rotors to come to rest is known as the brake delay time and is determined by the brake rate. The V3 allows you to adjust the brake delay time for the upper and lower rotors independently. To adjust the upper or lower rotor brake delay time, do the following:

1. Select the parameter corresponding to the rotor you want to adjust the brake rate, i.e. UPPER ROTOR BRAKE RATE XXXX SEC, or LOWER ROTOR BRAKE RATE XXXX SEC (R).

2. Set the rotor wind-down time (XXXX) for the brake rate. Play some notes on your keyboard with the rotary speaker effect turned on and listen to the change in slow-down time as you switch between BRAKE and SPIN functions. Adjust to taste. Repeat this step for each rotor.

Setting Upper/Lower Rotor Microphone Angle

1. Select parameter UPPER ROTOR MIC ANGLE XXX DEG (R) or LOWER ROTOR MIC ANGLE XXX DEG (R), depending on which rotor microphone angle you which to adjust.

2. Set the upper rotor or lower rotor microphone angle (XXX) (in degrees) from 00 (no stereo separation) to 180° (maximum stereo separation). Play some notes on you keyboard with the rotary speaker effect turned on as you adjust the microphone angle, adjust to taste.

Controlling the Rotary Speaker Effect through MIDI

The V3's rotating speaker effect can be controlled through MIDI giving you full access to control many of its features from a remote MIDI controller. This has many important implications because it opens up a many possibilities for real time control of the rotary speaker effect during live performance, recording sessions, MIDI sequences, etc. Most of the parameters associated with the V3's rotary speaker effect can be controlled via MIDI. These parameters are listed in the ROTATING SPEAKER PARAMETERS section. The following is a list of all of the V3's rotary speaker functions that can be controlled via MIDI:

    Rotary Speaker Bypass
    Rotary Speaker SLOW/FAST
    Rotary Speaker Brake
    Rotor Balance
    Upper and Lower Rotor Microphone Distance
    Upper and Lower Rotor Pitch Modulation
    Upper and Lower Rotor Fast Speed
    Upper and Lower Rotor Slow Speed
    Upper and Lower Rotor Acceleration
    Upper and Lower Rotor Deceleration
    Upper and Lower Rotor Brake Rate
    Upper and Lower Rotor Microphone Angle

To control any of the above rotary speaker functions via MIDI, simply assign the MIDI controller number to the corresponding MIDI controller parameter listed in the MIDI CONTROLLER PARAMETERS section.

Since there are a multitude of ways to use MIDI to control the rotary speaker effect and since everyone has different requirements, each dictated by his or her particular application and the limitations of their MIDI equipment, it is beyond the scope of this manual to cover every possible combination, configuration and application of MIDI control over the V3's rotary speaker effect. Instead, we have chosen a few examples that cover typical applications which will help you in creating your own MIDI setups.

Example #1: Controlling Rotor Velocity with the MOD Wheel

Select parameter ROTATING SPEAKER FAST/SLOW CONTROL (C) and assign your MIDI keyboard's MOD wheel MIDI control number (usually control #1) to this parameter. Since the MOD wheel is a continuous controller, it will output a control value of 0 through 127 depending on what position it is set to. To select the FAST rate simply flip the MOD wheel all the way up (on most keyboards up means away from you) or all the way down (towards you) for the SLOW rate. The rotating speaker simulation will begin changing speed after the MOD wheel crosses the midway point (when the control value switches between 63 and 64).

Example #2: Controlling Rotor Velocity with Aftertouch

1. Select parameter ROTATING SPEAKER FAST/SLOW CONTROL (C) and assign to it Aftertouch (AFT).

2. Now when you play a note on a keyboard that transmits Aftertouch, the upper rotor and lower rotor velocity will will toggle between FAST and SLOW as you press hard on the keys.

Example #3: Using a Continuous Controller to Adjust the Rotor Fast Speed

1. Select parameter UPPER ROTOR FAST CONTROL (C) and assign to it the MIDI controller number (XXX) for the MIDI controller you which to use. This could be the MIDI control number of a MIDI slider in a keyboard or other MIDI control device.

2. Select parameter LOWER ROTOR FAST CONTROL (C).

3. Since we want to control the speed of both rotors simultaneously, select the same MIDI control number for the lower rotor fast control. This allows for real-time control of the rotor speed which can be used instead of the normal acceleration/deceleration function.

Note that in this example, one MIDI controller was assigned to two parameters. We could have also assigned a different controller to each parameter. However there are cases where having too many controllers becomes impractical which is where having the ability to assign one controller to more than one parameter becomes very useful.

Example #4: Using a MIDI ON/OFF Push Button Controller to Bypass the Rotary Speaker

1. Select parameter ROTARY SPEAKER BYPASS CONTROL (C) and assign to it the MIDI control number of the ON/OFF controller in your MIDI keyboard or other MIDI controller device.

2. To bypass the rotary speaker effect, simply press the MIDI ON/OFF push button. When the MIDI ON/OFF controller transmits a value between 0 and 63, the rotary speaker effect will be bypassed. When the value is between 64 and 127, the bypass will be removed and the rotary speaker effect will be enabled.

Programming Rotary Speaker Setups Using External MIDI Controllers

One of the many useful features of having MIDI control over the rotary speaker parameters is in programming your own rotary speaker setups. For example: Using one of the many universal MIDI controllers available today, you can assign a MIDI controller to any or all of the rotating speaker simulations parameters. In this way you can "tweak" more than one parameter at a time without having to go into edit mode. This makes the creation process a lot easier and less tedious. Once you have the right combination of settings for a particular setup, you can then save the edit buffers settings to the rotating speaker setup used by the current patch:

In order to access a rotary speaker setup you need to either know what patch uses the rotary speaker setup or you have to enter an arbitrary patch and select the particular rotary speaker setup from the 20 available setups. If the latter case is true performs steps 1 through 3 below; otherwise, select the patch with the rotary speaker setup you want to edit and skip step 1.

1. Enter EDIT MODE then select parameter ROTARY SPEAKER TYPE (P) and select the rotary speaker setup you want to edit. Save your changes and exit.

2. Tweak the rotary speaker parameters by making adjustments through your external MIDI controller.

3. Once you are satisfied with your settings, enter EDIT MODE (press the EDIT button), the press the EDIT button again, save and exit.

Now all the changes you made through your MIDI controller are saved in the rotary speaker setup you selected above.

Editing More than one Rotary Speaker Setup During an Edit Session

At some point you may want to edit one or more rotary speaker setups without leaving EDIT MODE. Since you may not know off hand which rotary speaker setups are assigned to which patches, it's a good idea to use one patch as a dummy patch to edit as many rotary speaker setups as you like. To edit more than one rotary speaker setup at a time, do the following:

1. Select an arbitrary patch then write down the rotary speaker setup assigned to it.

2. Select the rotary speaker setup you which to edit, make your changes and save.

Using foot switches to control the Rotary Speaker Effect

The V3 provides two foot switch inputs on the rear panel to control two rotary speaker effect functions; one labeled BRAKE FT SW to control the rotor BRAKE and another labeled S/F FT SW to switch between SLOW and FAST velocity. Both of these switches are momentary type. Pressing the foot switches will toggle between SLOW and FAST or cause the rotors to BRAKE, depending on which one is pressed. When either of these rotary speaker functions are controlled via foot switches, the LED indicator on the front panel for the corresponding front panel control will indicate the state of the functions. The S/F FT SW also controls the model 122 speaker output.

E D I T I N G   A N D    C U S T O M I Z I N G
M I D I   C O N T R O L L E R    M A P S

MIDI controllers are capable of controlling many parameters and features of the V3. There are ten global MIDI CONTROLLER MAPs available for assignment to a particular patch. These maps allow assignment of various V3 functions to a MIDI controller or MIDI aftertouch. Each map may be customized (edited) to suit either the functions of different MIDI environments such as different keyboards to make the greatest use of a keyboard with a limited controller implementation. For example, a keyboard may only send a control for its Modulation Wheel: The Modulation Wheel can be used for different functions on different patches by utilizing different MIDI CONTROLLER MAPs programmed appropriately. The following paragraphs contain examples of how to use the MIDI Controller Maps.

Assigning a MIDI Controller Map to a Patch

To assign one of the ten global MIDI Controller Maps to any of the V3's 128 patches first make sure you are editing the patch where you want to make the assignment, then do the following:

1. 1. Select parameter CONTROL MAP #X (C).

2. 2. Select the MIDI CONTROLLER MAP number (XX). The name of the MIDI CONTROLLER MAP will be displayed as you select the MIDI CONTROLLER MAP number.

Naming MIDI CONTROLLER MAP

You can give a unique name to any of the ten MIDI CONTROLLER MAPs. To name a MIDI CONTROLLER MAP do the following:

1. Select parameter EDIT CONTROLLER MAP NAME (C).

2. The cursor will fall under the left-most or right-most character position, depending on which direction you are turning the cursor knob. Select a letter for each character position by turning the DATA/PRESET control knob. You can use up to 10 characters per name.

Assigning a MIDI Controller for Main Drawbar Control

You can assign any MIDI continuous controller or aftertouch to adjust the main drawbar setting for the V3. Like all MIDI controller assignments, any one controller can control more than one V3 function. It's possible to assign one MIDI controller to change all or some of the V3's drawbar setting. To make this assignment:

1. Select meny item YY' DRAWBAR CTRL NUMBER XXX (C).
   (YY = 16', 5-1/3', 8', 4', 2-2/3', 2', 1-3/5', 1-1/3', 1')

2. Set the value (XXX) to be the control desired control number (0-121), off or aftertouch. The off (OFF) setting allows the V3 to ignore all MIDI controls for the specified function. Aftertouch (AFT) assigns the function to MIDI aftertouch.

Assigning a MIDI Controller for Auxiliary Drawbar Control

You can assign any MIDI continous controller or aftertouch to adjust the auxiliary drawbar setting for the V3. The auxiliary drawbar setting is the one which the V3 will morph to when using the MIDI morph function. Like all MIDI controller assignments, any one controller can control more than one V3 function. It's possible to assign one MIDI controller to change all or some of the V3's auxiliary drawbar settings. To make this assignment:

1. Select menu item AUX YY' DRAWBAR CTRL NUMBER XXC (C).
   (YY = 16', 5-1/3', 8', 4', 2-2/3', 2', 1-3/5', 1-1/3', 1' )

2. Set the value (XXX) to be the control desired control number (0-121), off, or aftertouch. The off (OFF) setting allows the V3 to ignore all MIDI controls for the specified function. Aftertouch (AFT) assigns the function to MIDI aftertouch.

Assigning a MIDI Controller to the Drawbar Morph Function

The V3's MIDI morph function allows the player to change smoothly from the main drawbar setting (reffered to in this manual as drawbar setting) to an auxiliary drawbar setting. To assign a MIDI continuous controller or aftertouch asssigned to perform this function, do the following:

1. Select menu item DRAWBAR MORPH CTRL NUMBER XXX (C).

2. Set the value (XXX) to be the control desrired control number (0-121), off, or aftertouch. The off (OFF) setting allows the V3 to ignore all MIDI controls for the specified function. The aftertouch (AFT) assigns the function to a MIDI control.

Assigning MIDI Controller to Toggle the Rotating Speaker's Sound

Besides the front panel push-button and rear panel foot switch input, the V3's rotating speaker speed can be toggled by a MIDI controller or aftertouch. An assigned MIDI controller will change the rotating speaker's speed after passing through the halfway point of its travel. When the function is assigned to aftertouch, aftertouch will toggle the speed alternately rather than just setting the rotating speaker to fast or slow depending on pressure. To assign this function:

1. Select menu item R SPEAKER SL/FAST CTRL NUMBER XXX (C).

2. Set the value (XXX) to be the control desired control number (0-121), off, or aftertouch. The off (OFF) setting allows the V3 to ignore all MIDI controls for the specified function. Aftertouch (AFT) assigns the function to MIDI aftertouch.

Assigning a MIDI Controller to the Expression Function

The V3's expression level (similar to a loudness control) can be controlled from an analog pedal plugged into the rear of the unit or by a MIDI continuous controller. To assign a MIDI controller for this function do the following:

1. Select menu item MIDI EXPRESSION CTRL NUMBER XXX (C).

2. Set the value (XXX) to be the control desired control number (0-121), off, or aftertouch. The off (OFF) setting allows the V3 to ingnore all MIDI controls for the specified function. The aftertouch (AFT) assigns the function to MIDI aftertouch.

Summary of MIDI Functions

The following is a summary of the V3's functions which can be controlled by MIDI controllers and references to the suitability of controller types:

List of V3's MIDI Functions	Functions Best Suited For Continuous Controllers	Functions Best Suited for On/Off Controllers	Functions which cannot be controlled by aftertouch
Main Drawbars	X
Aux Drawbars	X
Drawbar Morph	X
MIDI Volume	X
MIDI Expression	X
Percussion On/Off		X
Perc. Volume Normal/Soft		X
Perc. Decay Slow/Fast		X
Perc. Harmonic 2/3		X
Chorus/Vibrato On/Off		X
Chorus/Vibrato Select	X		X
Rotary Speaker Bypass		X	X
Rotary Speaker Slow/Fast		X	X
Rotary Speaker Brake On/Off		X	X
Overdrive Mix	X
Keyclick Level	X
Generator Leakage Level	X
Upper/Lower Mic Distance	X
Upper/Lower Rotor Pitch Mod	X
Upper/Lower Rotor Fast Speed	X
Upper/Lower Rotor Slow Speed	X
Upper/Lower Rotor Accel	X
Upper/Lower Rotor Decel	X	<